Preview build — page text is a draft awaiting human review. Code badges come from real compiles. The flasher is real but not yet hardware-tested; the Playground is still a preview.
Get Started
Wi-Fi Signal Logger: the finished build
ESP32-C3 SuperMiniNetwork & ISP tools

Wi-Fi signal strength logger with live graph (ESP32-C3 SuperMini + OLED)

A pocket RSSI meter with a live graph — find dead spots before you buy an extender.

Difficulty
Easy
Build time
45 min
Parts cost
₹890 · $10
Verified — core esp32 3.3.12, Adafruit SSD1306 2.5.17, 3 Nov 2026Compile-only
Flash to my boardOpen in Playground

Community draft — report a mistake

Parts list

PartQtyApprox.Buy
ESP32-C3 SuperMini1₹230Buy ESP32-C3 SuperMini
0.96" SSD1306 I2C OLED (4-pin)1₹220Buy 0.96" SSD1306 I2C OLED (4-pin)
USB power bank + USB-C cable1₹400Buy USB power bank + USB-C cable
Jumper wires (female–female)4₹40Buy Jumper wires (female–female)
Total₹890

Affiliate disclosure: “Buy” links may earn FlashReady a small commission at no extra cost to you. Prices are indicative.

Wiring

ESP32-C3 SuperMiniOnly the pins used are shown · 3.3 V logicSSD1306 OLED 0.96″ (128×64, I2C)GND3V36 · 67 · 7GNDVCCSCLSDA
Every connection
ESP32-C3 SuperMiniSSD1306 OLED 0.96″ (128×64, I2C)WireNotes
7SCLyellowGPIO7
6SDAblueGPIO6 — keeps I2C off strapping pins 8 and 9
3V3VCCred
GNDGNDblack

Board quirks: The SuperMini uses native USB. Its profile turns on "USB CDC On Boot", otherwise <code>Serial</code> prints nothing. GPIO8 drives the on-board LED and GPIO9 is the BOOT button; both are strapping pins, so I2C goes on GPIO6/7 instead. The SuperMini’s small ceramic antenna is weaker than a DevKit’s PCB antenna, so readings run a few dB lower than your phone. Compare places with each other, not with your phone’s bars. The ESP32-C3 only does 2.4 GHz. This measures your 2.4 GHz network, not the 5 GHz one.

Code

wifi-signal-logger.inoArduino C++Open in PlaygroundOpen in PlaygroundFlash
// Wi-Fi signal logger — ESP32-C3 SuperMini + SSD1306 OLED
// OLED on I2C: SDA GPIO6, SCL GPIO7 (GPIO8/9 are strapping pins — the LED and BOOT button —
// so this sketch keeps I2C off them). Walk around the house and watch the RSSI graph;
// Serial prints CSV (seconds,rssi_dbm) for a spreadsheet. Board option: USB CDC On Boot = Enabled.
#include <WiFi.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
#include "fr_settings.h"

const char* WIFI_SSID = "YOUR_SSID";
const char* WIFI_PASS = "YOUR_PASSWORD";
// Filled in from the FlashReady flasher over USB (kept on the board), or type the values above.
FrSetting SETTINGS[] = {{"wifi_ssid", &WIFI_SSID, true}, {"wifi_pass", &WIFI_PASS, true}};

constexpr uint8_t SDA_PIN = 6;
constexpr uint8_t SCL_PIN = 7;

Adafruit_SSD1306 oled(128, 64, &Wire, -1);
int8_t samples[128];
uint8_t n = 0;
int minR = 0, maxR = -127;

const char* quality(int r) {
  if (r >= -55) return "Excellent";
  if (r >= -67) return "Good";
  if (r >= -75) return "Fair";
  return "Weak";
}

void setup() {
  Serial.begin(115200);
  frSettingsBegin(SETTINGS);
  Wire.begin(SDA_PIN, SCL_PIN);
  if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println("OLED not found at 0x3C");
  if (*WIFI_SSID) WiFi.begin(WIFI_SSID, WIFI_PASS);
  else Serial.println("Wi-Fi off — no Wi-Fi name set. Flash from flashready.in or type it into the code.");
  Serial.println("seconds,rssi_dbm");
}

void loop() {
  bool up = WiFi.status() == WL_CONNECTED;
  int r = up ? WiFi.RSSI() : -100;
  if (n < 128) samples[n++] = r;
  else {
    memmove(samples, samples + 1, 127);
    samples[127] = r;
  }
  if (up) {
    minR = min(minR, r);
    maxR = max(maxR, r);
  }

  oled.clearDisplay();
  oled.setTextColor(SSD1306_WHITE);
  oled.setTextSize(1);
  oled.setCursor(0, 0);
  if (up) oled.printf("%d dBm  %s", r, quality(r));
  else oled.print("Wi-Fi not connected");
  oled.setCursor(0, 10);
  oled.printf("min %d  max %d", up ? minR : 0, up ? maxR : 0);
  // Graph: -30 dBm at the top, -100 dBm at the bottom of the 44 px area
  for (uint8_t i = 1; i < n; i++) {
    int y0 = 63 - (samples[i - 1] + 100) * 44 / 70;
    int y1 = 63 - (samples[i] + 100) * 44 / 70;
    oled.drawLine(i - 1, y0, i, y1, SSD1306_WHITE);
  }
  oled.display();

  Serial.printf("%lu,%d\n", millis() / 1000, r);
  delay(1000);
}

Arduino IDE: keep fr_settings.h in the same folder as the .ino (tab menu → New Tab, same name). Flashing from this page doesn’t need it.

fr_settings.hArduino C++
// fr_settings.h — FlashReady on-board settings (Wi-Fi name, phone number, ...) over USB.
//
// Why: the pre-built file on flashready.in is the same for everyone, so your own settings
// can't be inside it. Instead the board asks for them over USB serial and keeps them in
// its EEPROM. If you use Arduino IDE you can still type them into the constants in the
// sketch — this file then changes nothing except a 2-second pause at start-up.
//
// The protocol, in plain words (one text line each way, ending in \n, at 115200 baud):
//  1. Right after Serial.begin(115200) the board prints
//       FR?SETTINGS v1 keys=wifi_ssid,wifi_pass missing=wifi_pass
//     "missing" lists the required settings that still have no real value.
//  2. If nothing is missing it listens for 2 seconds and then carries on. If something is
//     missing it keeps listening, printing the line again every 2 seconds, for up to
//     30 seconds; then it carries on anyway and the sketch skips whatever needs the
//     missing value (an alarm still sounds, it just can't send the SMS).
//  3. The flasher answers   FR!SET wifi_ssid=My%20Home&wifi_pass=secret
//     (values URL-encoded). The board stores them and answers FR!OK, then carries on with
//     the new values. Errors: FR!ERR unknown <key>, FR!ERR long <key> (nothing is stored).
//     A key that is left out keeps its stored value; "key=" (empty) removes it.
//     "FR!SET" with nothing after it means "carry on now": FR!OK, nothing is stored.
//  4. FR!CLEAR wipes everything that was stored, answers FR!OK and keeps listening.
//  Other lines are ignored.
//
// A stored value wins over the constant in the sketch. A constant that is still a
// placeholder ("YOUR_SSID", "your-wifi", "+91XXXXXXXXXX") or empty counts as not set.
//
// EEPROM block at FR_SETTINGS_ADDR: 'F' 'R' 0x01, length (uint16, low byte first), then
// "key=value\n" lines. Uses FR_SETTINGS_SIZE bytes; move FR_SETTINGS_ADDR with a #define
// before the #include if your sketch uses EEPROM for something else.
//
// Use in a sketch:
//   const char* WIFI_SSID = "YOUR_SSID";
//   FrSetting SETTINGS[] = { {"wifi_ssid", &WIFI_SSID, true} };   // key, constant, required
//   void setup() { Serial.begin(115200); frSettingsBegin(SETTINGS); ... WiFi.begin(WIFI_SSID, ...); }
// After frSettingsBegin() each constant points at the value to use ("" if none is set).
#pragma once
#include <Arduino.h>
#include <EEPROM.h>
#include <string.h>

#ifndef FR_SETTINGS_ADDR
#define FR_SETTINGS_ADDR 0
#endif
#ifndef FR_SETTINGS_SIZE
#if defined(__AVR__)
#define FR_SETTINGS_SIZE 96  // 2 KB of RAM on an Uno: a phone number fits easily
#else
#define FR_SETTINGS_SIZE 512
#endif
#endif
#ifndef FR_LINE_MAX
#if defined(__AVR__)
#define FR_LINE_MAX 128
#else
#define FR_LINE_MAX 1024
#endif
#endif
#define FR_MAX_KEYS 8
#define FR_WAIT_MAX_MS 30000UL  // never wait longer than this for missing settings
#define FR_DATA_MAX (FR_SETTINGS_SIZE - 5)

struct FrSetting {
  const char* key;     // [a-z0-9_], as in settings.json
  const char** value;  // the sketch's constant; replaced by the value to use
  bool required;
};

// Stored settings in RAM as "key=value\0key=value\0" (only non-empty values).
static char frData[FR_DATA_MAX + 1];
static uint16_t frLen = 0;

static inline void frEepromBegin() {
#if defined(ESP32) || defined(ESP8266)
  static bool started = false;
  if (!started) EEPROM.begin(FR_SETTINGS_ADDR + FR_SETTINGS_SIZE);
  started = true;
#endif
}

static inline void frLoad() {
  frEepromBegin();
  frLen = 0;
  frData[0] = 0;
  if (EEPROM.read(FR_SETTINGS_ADDR) != 'F' || EEPROM.read(FR_SETTINGS_ADDR + 1) != 'R' || EEPROM.read(FR_SETTINGS_ADDR + 2) != 1) return;
  uint16_t n = EEPROM.read(FR_SETTINGS_ADDR + 3) | (EEPROM.read(FR_SETTINGS_ADDR + 4) << 8);
  if (n > FR_DATA_MAX) return;
  for (uint16_t i = 0; i < n; i++) {
    char c = EEPROM.read(FR_SETTINGS_ADDR + 5 + i);
    frData[i] = c == '\n' ? '\0' : c;
  }
  frData[n] = 0;
  frLen = n;
}

static inline void frPut(int addr, uint8_t b) {
#if defined(__AVR__)
  EEPROM.update(addr, b);
#else
  EEPROM.write(addr, b);
#endif
}

static inline void frSave() {
  frEepromBegin();
  frPut(FR_SETTINGS_ADDR, 'F');
  frPut(FR_SETTINGS_ADDR + 1, 'R');
  frPut(FR_SETTINGS_ADDR + 2, 1);
  frPut(FR_SETTINGS_ADDR + 3, frLen & 0xFF);
  frPut(FR_SETTINGS_ADDR + 4, frLen >> 8);
  for (uint16_t i = 0; i < frLen; i++) frPut(FR_SETTINGS_ADDR + 5 + i, frData[i] ? frData[i] : '\n');
#if defined(ESP32) || defined(ESP8266)
  EEPROM.commit();
#endif
}

// The stored value for key, or nullptr.
static inline const char* frStored(const char* key) {
  size_t kl = strlen(key);
  for (uint16_t i = 0; i < frLen; i += strlen(frData + i) + 1) {
    if (strncmp(frData + i, key, kl) == 0 && frData[i + kl] == '=') return frData + i + kl + 1;
  }
  return nullptr;
}

// Empty, "your_…" / "YOUR-…" / "your …", or a "+91XXXX…" phone number.
static inline bool frIsPlaceholder(const char* v) {
  if (!v || !*v) return true;
  if (strncasecmp(v, "your", 4) == 0 && (v[4] == '_' || v[4] == '-' || v[4] == ' ')) return true;
  return v[0] == '+' && strstr(v, "XXXX") != nullptr;
}

// The stored value for key, else the fallback constant; "" if that is a placeholder.
static inline const char* frSettingsGet(const char* key, const char* fallback) {
  const char* v = frStored(key);
  if (!v) v = fallback;
  return frIsPlaceholder(v) ? "" : v;
}

static inline bool frIsMissing(const FrSetting& s) {
  return s.required && !*frSettingsGet(s.key, *s.value);
}

static inline void frRequest(FrSetting* s, uint8_t n) {
  Serial.print(F("FR?SETTINGS v1 keys="));
  for (uint8_t i = 0; i < n; i++) {
    if (i) Serial.print(',');
    Serial.print(s[i].key);
  }
  Serial.print(F(" missing="));
  bool first = true;
  for (uint8_t i = 0; i < n; i++) {
    if (!frIsMissing(s[i])) continue;
    if (!first) Serial.print(',');
    Serial.print(s[i].key);
    first = false;
  }
  Serial.print('\n');
}

static inline void frReply(const __FlashStringHelper* what, const char* key) {
  Serial.print(what);
  Serial.print(key);
  Serial.print('\n');
}

static inline int8_t frHex(char c) {
  if (c >= '0' && c <= '9') return c - '0';
  c |= 0x20;
  return (c >= 'a' && c <= 'f') ? c - 'a' + 10 : -1;
}

// Percent-decodes in place. Drops NUL, CR and LF: they can't be stored.
static inline void frDecode(char* s) {
  char* o = s;
  for (; *s; s++) {
    char c = *s;
    if (c == '%' && frHex(s[1]) >= 0 && frHex(s[2]) >= 0) {
      c = (char)(frHex(s[1]) << 4 | frHex(s[2]));
      s += 2;
    }
    if (c != '\0' && c != '\n' && c != '\r') *o++ = c;
  }
  *o = 0;
}

// "k1=v1&k2=v2" (cut short if the line overflowed). Saves and returns true, or replies with an error.
static inline bool frSet(FrSetting* s, uint8_t n, char* p, bool overflow) {
  const char* upd[FR_MAX_KEYS] = {};
  while (*p) {
    char* amp = strchr(p, '&');
    bool last = !amp;
    if (amp) *amp = 0;
    char* eq = strchr(p, '=');
    if (eq) *eq = 0;
    if (*p) {
      if (last && overflow) {
        frReply(F("FR!ERR long "), p);
        return false;
      }
      uint8_t i = 0;
      while (i < n && strcmp(s[i].key, p) != 0) i++;
      if (i == n) {
        frReply(F("FR!ERR unknown "), p);
        return false;
      }
      char* v = eq ? eq + 1 : p + strlen(p);  // "key" alone = "key="
      frDecode(v);
      upd[i] = v;
    }
    if (last) break;
    p = amp + 1;
  }
  // Build the new block: for each key, the new value or the one already stored.
  char next[FR_DATA_MAX + 1];
  uint16_t len = 0;
  for (uint8_t i = 0; i < n; i++) {
    const char* v = upd[i] ? upd[i] : frStored(s[i].key);
    if (!v || !*v) continue;
    size_t kl = strlen(s[i].key), vl = strlen(v);
    if (len + kl + vl + 2 > FR_DATA_MAX) {
      frReply(F("FR!ERR long "), s[i].key);
      return false;
    }
    memcpy(next + len, s[i].key, kl);
    next[len + kl] = '=';
    memcpy(next + len + kl + 1, v, vl + 1);
    len += kl + vl + 2;
  }
  memcpy(frData, next, len);
  frData[len] = 0;
  frLen = len;
  frSave();
  return true;
}

// Handles one received line. Returns true once settings were saved (boot carries on).
static inline bool frCommand(FrSetting* s, uint8_t n, char* line, bool overflow) {
  if (strcmp(line, "FR!CLEAR") == 0) {
    frLen = 0;
    frData[0] = 0;
    frSave();
    Serial.print(F("FR!OK\n"));
    return false;
  }
  if (strncmp(line, "FR!SET", 6) != 0 || (line[6] != ' ' && line[6] != 0)) return false;  // not for us
  char* p = line + 6;
  while (*p == ' ') p++;
  if (*p && !frSet(s, n, p, overflow)) return false;  // empty FR!SET = carry on, store nothing
  Serial.print(F("FR!OK\n"));
  return true;
}

// Call right after Serial.begin(115200). Prints the request, waits as described at the top
// (30 s at most), then points every constant in the list at the value to use ("" = not set).
static inline void frSettingsBegin(FrSetting* s, uint8_t n) {
  frLoad();
  char line[FR_LINE_MAX];
  uint16_t len = 0;
  bool overflow = false;
  frRequest(s, n);
  unsigned long start = millis(), quietSince = start;
  while (millis() - start < FR_WAIT_MAX_MS) {
    int c = Serial.read();
    if (c >= 0) {
      quietSince = millis();
      if (c == '\r') continue;
      if (c != '\n') {
        if (len < FR_LINE_MAX - 1) line[len++] = (char)c;
        else overflow = true;
        continue;
      }
      line[len] = 0;
      bool saved = frCommand(s, n, line, overflow);
      len = 0;
      overflow = false;
      if (saved) break;
      continue;
    }
    if (millis() - quietSince < 2000) {
      delay(1);  // also keeps the ESP8266 watchdog fed
      continue;
    }
    len = 0;  // drop half a line
    overflow = false;
    bool missing = false;
    for (uint8_t i = 0; i < n; i++) missing |= frIsMissing(s[i]);
    if (!missing) break;
    frRequest(s, n);
    quietSince = millis();
  }
  for (uint8_t i = 0; i < n; i++) *s[i].value = frSettingsGet(s[i].key, *s[i].value);
}

template <size_t N>
static inline void frSettingsBegin(FrSetting (&s)[N]) {
  static_assert(N <= FR_MAX_KEYS, "fr_settings.h: at most FR_MAX_KEYS settings");
  frSettingsBegin(s, (uint8_t)N);
}

Compiled for c3supermini on esp32 3.3.12 with Adafruit SSD1306 2.5.17 · 3 Nov 2026

How it works

Before buying a Wi-Fi extender or moving the router, it helps to know where the signal really drops. This pocket meter shows Wi-Fi signal strength (RSSI) as a big number and a scrolling graph on an OLED. Run it from a power bank and walk around.

The ESP32-C3 SuperMini is a tiny, cheap board with Wi-Fi and native USB. It joins your network and reads the RSSI once a second. The top line shows the value in dBm with a label — Excellent (−55 or better), Good, Fair or Weak (below −75). The second line keeps the best and worst values seen.

Below that, the last 128 seconds are drawn as a graph from −30 dBm at the top to −100 dBm at the bottom. As you walk from room to room you see exactly where the signal falls off — behind a concrete wall, at the end of a corridor, or on the terrace.

Serial prints CSV lines (seconds,rssi_dbm), so with a laptop you can log a walk-through and plot it in a spreadsheet.

Troubleshooting

The board doesn’t show up as a COM port

Hold BOOT, tap RESET, release BOOT, then upload. After the first upload with CDC on boot it appears normally.

The OLED stays black

Check SDA is on pin 6 and SCL on pin 7. Run the I2C scanner with Wire.begin(6, 7).

"Wi-Fi not connected" all the time

Check the SSID and password, and that the network is 2.4 GHz. Some dual-band routers need the 2.4 GHz band enabled separately.

Upgrades

  • Scan all nearby networks and show which channel is least crowded.
  • Log readings with a room name to LittleFS and download a heat-map table.
  • Add a button to mark each spot as you walk around.

More projects

ECG Display

UnoMedium

See the P-QRS-T wave of a real heartbeat — the biology textbook diagram, live.

₹1,550 parts cost, about $18Verified core 1.8

Angithi CO Alarm

NanoEasy

Warns when carbon monoxide builds up from a charcoal heater in a closed room.

₹1,075 parts cost, about $13Verified core 1.8

Aquarium Controller

ESP32Medium

Steady 26 °C water, a timed light with a midday break, and a too-hot/too-cold beep.

₹2,095 parts cost, about $25Verified core 3.3

↑↓ to move · Enter to open